With the advance of the national environmental protection policy, the heavy-duty carton packaging has been widely used, followed by the vigorous development of heavy-duty carton manufacturers, the quality of heavy-duty cartons is also uneven, in order to make you more intuitive understanding of the standard of heavy-duty cartons, refer to the corrugated heavy-duty carton standard GB / t6543-2008, summarize the following three main points for your reference.

重型紙箱廠家貝爾泰結合 行業經驗，根據 重型紙箱GB/T6543-2008總結了如下3大標準：

Based on the industry experience and GB / t6543-2008, beltai, a heavy-duty carton manufacturer, summarized the following three standards:

1.重型紙箱外觀標準：

1. Appearance standard of heavy duty carton:

1)箱體紙箱成型后箱體方正，表面不允許有明顯的損壞和污跡，箱面不得有拼接，箱體各角無明顯的漏洞或包角。

1) After the box box is formed, the box is square, the surface is not allowed to have obvious damage and stains, the box surface is not allowed to have splicing, and the corners of the box have no obvious holes or corners.

2)印刷 箱面印刷圖文正確、清晰、墨色深淺一致、位置準確，不應有明顯偏斜。

2) The printed picture and text on the printing box surface are correct, clear, the ink color is consistent, the position is accurate, and there should be no obvious deviation.

3)釘合

3) Nailing

紙箱釘合應使用帶鍍層(銅、鋅)的低碳鋼扁絲，扁絲不應有銹斑、剝層、龜裂或其他使用上的缺外觀缺陷。紙箱接縫應釘牢、釘透，不得有疊釘、缺釘、翹釘、斷釘、曲釘、不轉角等缺陷。紙箱接頭釘合搭接舌邊的寬度為35一50mm采用斜釘或橫釘釘合，且箱釘應沿搭結舌邊的中線釘合。箱釘排列整齊、均勻，頭尾釘距頂、底面壓痕線不大于25mm。

Low carbon steel flat wire with coating (copper, zinc) shall be used for nailing cartons. The flat wire shall be free from rust, peeling, cracking or other appearance defects. The seams of cartons shall be nailed firmly and thoroughly, and there shall be no defects such as overlapping nails, missing nails, warping nails, broken nails, bent nails, no corner and so on. The width of the overlap tongue of the carton joint is 35-50 mm, and the box nails should be nailed along the middle line of the overlap tongue. The box nails shall be arranged orderly and evenly, and the distance between the head and tail nails and the indentation line on the top and bottom surface shall not be more than 25 mm.

4)粘合

4) Bonding

紙箱接頭所使用的粘合劑應是乙酸乙烯乳液或具有同等效果的其他粘合劑；接頭舌邊寬度適度，粘合劑涂布充分、均勻，粘合牢固。

The adhesives used for carton joints should be vinyl acetate emulsion or other adhesive with the same effect. The width of the joint tongue is moderate, the adhesive coating is sufficient and uniform, and the bonding is firm.

5)壓線

5) Line pressing

壓痕深淺一致，折線居中，不應有破裂現象；箱壁不允許有多余的壓痕線，壓痕線寬度值的規定如下

The indentation depth is consistent, the broken line is in the middle, and there should be no fracture phenomenon; No extra indentation line is allowed on the box wall. The width of indentation line is specified as follows

a)凹凸式壓痕線寬度:六層以下瓦楞紙箱的壓痕線寬度不大干17mm；七層瓦楞紙箱的壓痕線寬度不大于Zomm；

a) Concave and convex indentation line width: the indentation line width of corrugated box under six layers is not more than 17mm; The width of indentation line of seven layer corrugated box shall not be greater than zomm;

b)偏置式壓痕線寬度:箱內面的壓痕線與箱外面的壓痕線的偏置間距不大于20mm。

b) Offset indentation line width: the offset distance between the indentation line inside the box and the indentation line outside the box shall not be greater than 20 mm.

5)裁切刀口

5) Cutting edge

刀口光潔，切斷口表面裂損寬度不超過8mm.

The cutting edge is smooth and clean, and the width of fracture surface is no more than 8 mm

b)偏置式壓痕線寬度:箱內面的壓痕線與箱外面的壓痕線的偏置間距不大于20mm。

b) Offset indentation line width: the offset distance between the indentation line inside the box and the indentation line outside the box shall not be greater than 20 mm.

今天的重型紙箱廠家精彩內容就給大家分享到這了，更多的精彩內容請點擊我們的網站http://m.hzlyfs.cn進行關注留言，后續會有更多的精彩內容為您呈現.

Today's heavy-duty carton manufacturers wonderful content to share with you, more wonderful content please click on our website http://m.hzlyfs.cn Follow the message, there will be more wonderful content for you